BoxFinish-Er Pre Installation Checklist

We are excited to embark on this journey with you and are committed to ensuring a seamless installation of your BoxFinish-ER.

To facilitate a smooth and timely setup, we kindly ask you to complete the Pre-Installation Checklist available on our portal. You can access the form here : Pre-Installation Checklist.

Please remember that this checklist must be submitted at least 2 weeks prior to your scheduled installation date. Failure to do so may result in the cancellation of your installation appointment.

In this section, you will find detailed explanations of the requirements for your BoxFinish-ER. These guidelines are essential to ensure optimal performance and a successful installation. By adhering to these requirements, you can help us provide the best possible experience with your equipment.

Inline dryer: The compressed air supply must be dried using an inline dryer.

Air cleanliness: The compressed air supplied must be free of particles larger than 5 microns.

Clean air is essential to avoid clogging or damaging the machine's internal components.

Air supply capacity:

The BoxFinish-Er need a consistent air flow of 10 CFM at 100 PSI (100% duty cycle). If the air supply fluctuates or is insufficient, the machine may not function correctly.

Pressure maintenance:

Compressed air pressure must remain steady at 100 PSIG. To maintain machine efficiency and avoid interruptions during operation.

Air connection size:

The compressed air line connection is a quick connects ¼”.

Conclusion: Clean, dry, and stable compressed air is critical for the smooth operation of the BoxFinish-ER. Inadequate air quality or supply can cause malfunctions, requiring additional service visits.

120V, 15A circuit:

Ensurea 120V, 15A circuit is available for the machine.  The BoxFinish-ERdraws approximately 5A.

Conclusion: Proper power supply ensures the machine runs safely and efficiently. Incorrect wiring or underpowered circuits could lead to failures during operation.

Ethernet connection:

In order to provide you the support you deserve A hard-wired Ethernet connection must be available. This connection allows for remote diagnostics, updates, and communication with the machine.

Temperature control:

Maintain a room temperature between 60-65°F (16-18°C) to ensure the machine operates in optimal conditions. Extreme temperatures can affect the performance and longevity of the equipment.

Humidity control: Maintain humidity levels between 40-60% relative humidity to avoid corrosion or moisture-related damage to the machine components.

Conclusion: A stable network and controlled environment are necessary to ensure the machine performs reliably, avoiding issues caused by excessive heat, cold, or humidity.

Compressor installation photo: A clear picture of your compressor installation, including the nameplate, must be Include in the form.

Explanation: We request this photo to confirm that your air system is properly installed and ready to handle the demands of the BoxFinish-ER, avoiding delays during installation.

Local approvals: Ensure that all necessary local and state approvals have been obtained for operating the machine with cannabis. This ensures compliance with regulations and prevents any legal or operational issues.

Operators and technicians: All personnel responsible for operating and maintaining the machine should be prepared for training. This includes having adequate staff available to undergo the required training sessions.

Explanation: It's essential to have all necessary legal permits and trained personnel ready to ensure the machine operates smoothly from the start.

Product quality: The product (oil, rosin, distillate) used in the machine must be free of solid particles and filtered to ensure smooth operation. The recommended viscosity is less than 200 centipoise (cp), similar to honey. The optimal ratio is 80/20.

Temperature control: The maximum warming temperature for the product should not exceed 100°C to avoid damaging the machine or the product.

Pre-roll consistency: Ensure that pre-rolls are prepared in advance for the training session, with a consistent height variation of +/- 2mm and a moisture content of 9-15%.

Tray availability: Make sure there are enough trays on hand for the training session, and they must be the same trays supplied to fit the machine’s attachment plate.

Explanation: Consistent and properly prepared products and pre-rolls are essential for the training session to demonstrate the machine’s full capabilities. Using the correct trays and pre-rolls ensures the training goes smoothly and the machine functions as expected.

By following these steps and ensuring all requirements are met, you will facilitate a successful installation of your BoxFinish-ER machine. If you have any questions or concerns, please don’t hesitate to contact us through your Client Portal.

If you haven't registered yet, please sign up for the Client Portal. Detailed instructions can be found in this document: How to Sign Up on the Portal.

From the PreRoll-Er Team

Welcome to our extended family! We sincerely hope our exceptional equipment meets your needs. Remember, our clients are our top priority, and we are dedicated to providing you with the support you deserve.

Thank you for choosing us!